For a more detailed technical presentation, click here

Feeder

– The machine is equipped with a nonstop feeding device with speeds of up to 120 sheets per minute.
– There are 2 suction cups each for lifting paper and 2 other suction cups for moving paper. Height and angle of suction heads are easily adjustable.
– Micro-adjustment is available for transversal position of pile table
– Precision electronic double sheet detector
– Maximum pile height up to 1300mm
– Pre loader is available as optional
– Optional; 1. pre loader for continuous run. 2. anti static air blowing device for diecutting thin paper or plastic sheets.
– Sheet thickness of 80g/m2 – E flute corrugated.

Feeder

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– The speed of the feeding belt is easily adjustable for perfect sheet control.
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– Single position engagement ensuring the 1st sheet after a re-start always gets fed to the front lays for timesaving and material saving make ready
– The speed of the feeding belt is easily adjustable for perfect sheet control.
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– The speed of the feeding belt is easily adjustable for perfect sheet control.
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.

– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.

– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.

– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.

– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Foil Stamping Section

Yoco can tailor-make professional solutions for you, whatever your circumstances. Our design is highly flexible, an easy mix and match can provide you the optimal production solution.

Patented design 2- direction foil feeding system, firstly introduced by Yoco make it possible to stamp the foils in longitudinal and transversal direction at the same time, this helps greatly in saving waste foils as well as the time to change foil. Some products can even be finished at ONE go.

– Maximum foil stamping speed is 6500 sheets per hour.

– Powerful & precise servo motor from OMRON japan capable to handle foil pilling in long distance and at high speed.

Foil Stamping Section

Yoco can tailor-make professional solutions for you, whatever your circumstances. Our design is highly flexible, an easy mix and match can provide you the optimal production solution.

Patented design 2- direction foil feeding system, firstly introduced by Yoco make it possible to stamp the foils in longitudinal and transversal direction at the same time, this helps greatly in saving waste foils as well as the time to change foil. Some products can even be finished at ONE go.

– Maximum foil stamping speed is 6500 sheets per hour.

– Powerful & precise servo motor from OMRON japan capable to handle foil pilling in long distance and at high speed.

Honeycomb Plate

– The eight pieces gripper bar design creates a bigger room for foil stamping section. It makes the adjustment of foil easier and more user-friendly.
– Longitudinal foil feeding unit can handle maximum foil size 250mm in diameter, sufficient space for easy operation
– Adjustment of the pressing roller and foil feeding is very easy
– Maximum foil stamping speed is 6500 sph
– Servo motor from japan Omron capable to handle pull foil in large area and at high speed.
– Computerised control display system and touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Honeycomb Plate

– The eight pieces gripper bar design creates a bigger room for foil stamping section. It makes the adjustment of foil easier and more user-friendly.
– Longitudinal foil feeding unit can handle maximum foil size 250mm in diameter, sufficient space for easy operation
– Adjustment of the pressing roller and foil feeding is very easy
– Maximum foil stamping speed is 6500 sph
– Servo motor from japan Omron capable to handle pull foil in large area and at high speed.
– Computerised control display system and touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Main Motor

– Inverter-controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Main Motor

– Inverter-controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Unwinding Unit

– The unwinding unit is worked by motor. The foil can be easily installed in the delivery unit.

Unwinding Unit

– The unwinding unit is worked by motor. The foil can be easily installed in the delivery unit.

Rewinding Unit

– The rewinding unit it inside the foil sections. It has the shortest distance for the foil rewinding to avoid foil breaking. The used foil can be easily taken out.

Rewinding Unit

– The rewinding unit it inside the foil sections. It has the shortest distance for the foil rewinding to avoid foil breaking. The used foil can be easily taken out.

Delivery Section

– With auxiliary delivery table can realise non-stop delivery
– Side delivery guide board drive by air cylinder, front paper guide brush and side air blow system, all strength and degree can be adjusted so that all kinds of paper, no matter running at low or height speed, will be aligned at delivery section.
– At the delivery section there is change speed system which can control the paper movement at feeder, easier to adjust delivery
– Adjustable depressor brush helps unloading paper from grippers and piling up paper
– Maximum pile height up to 1020mm
– Automatic auxiliary belt table available for nonstop delivery

Delivery Section

– With auxiliary delivery table can realise non-stop delivery
– Side delivery guide board drive by air cylinder, front paper guide brush and side air blow system, all strength and degree can be adjusted so that all kinds of paper, no matter running at low or height speed, will be aligned at delivery section.
– At the delivery section there is change speed system which can control the paper movement at feeder, easier to adjust delivery
– Adjustable depressor brush helps unloading paper from grippers and piling up paper
– Maximum pile height up to 1020mm
– Automatic auxiliary belt table available for nonstop delivery

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, hence to prolong the lifetime of the cutting plate.

– Accurate positioning of cutting chase controlled by precision photocell sensors with automatic chase lock device

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, hence to prolong the lifetime of the cutting plate.

– Accurate positioning of cutting chase controlled by precision photocell sensors with automatic chase lock device

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Main Drive System

– The patented toggle design contributes to maximum diecutting pressure as 400 to 200 tons.
– The required pressure can be easily set up on touch screen, controlled by electrical pressure adjustment system.
– Digital display of pressure data facilitates set up of repeat jobs.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Main Drive System

– The patented toggle design contributes to maximum diecutting pressure as 400 to 200 tons.
– The required pressure can be easily set up on touch screen, controlled by electrical pressure adjustment system.
– Digital display of pressure data facilitates set up of repeat jobs.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

JY85-T – Automatic Diecutting and Foil Stamping Machine