yoco-logo

YOCO JY-106E
Automatic Diecutter

For a more detailed technical presentation, click here

Feeder

– Equipped with world famous German design feeding system offered by KBA-MMS
– Maximum pile height up to 1600mm
– Equipped with non-stop feeding device
– There are 4 suction cups to lift the sheet and 5 other suction cups for moving the sheet
– Height and angle of suction heads are easily adjustable.
– The ascend and descend of the pile table can be adjusted by double-speed control system.
– Micro-adjustment is available for transversal position of pile table
– Lateral blowing system is adopted to enhance paper separation.
– The machine is equipped with electronic sensors to detect double sheets during operation.
– Sheet thickness of 1.5-5mm corrugated board.

Feeder

– Equipped with world famous German design feeding system offered by KBA-MMS
– Maximum pile height up to 1600mm
– Equipped with non-stop feeding device
– There are 4 suction cups to lift the sheet and 5 other suction cups for moving the sheet
– Height and angle of suction heads are easily adjustable.
– The ascend and descend of the pile table can be adjusted by double-speed control system.
– Micro-adjustment is available for transversal position of pile table
– Lateral blowing system is adopted to enhance paper separation.
– The machine is equipped with electronic sensors to detect double sheets during operation.
– Sheet thickness of 1.5-5mm corrugated board.

Feeding Table

– Feeding belt provided by HABASIT, Switzerland.

– The installation of an anti-obstacle device on the feeding table is to prevent obstacles from entering into the machine.

– Single position engagement ensuring the 1st sheet after a re-start always gets fed to the front lays for timesaving and material saving make ready

Feeding Table

– Feeding belt provided by HABASIT, Switzerland.

– The installation of an anti-obstacle device on the feeding table is to prevent obstacles from entering into the machine.

– Single position engagement ensuring the 1st sheet after a re-start always gets fed to the front lays for timesaving and material saving make ready

Side Lay

– Accurate paper registration is achieved by using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays.
– The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Side Lay

– Accurate paper registration is achieved by using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays.
– The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Heating Element

– Top heating plate

– Lower heating plate

– Top heating plate + lower heating plate, can achieve max diecutting speed at 5000 sph

Heating Element

– Top heating plate

– Lower heating plate

– Top heating plate + lower heating plate, can achieve max diecutting speed at 5000 sph

Stripping Section

– Triple action movement with upper, middle and lower stripping frame.

– Stripping pins or male / female die are available for different stripping jobs.

– Centreline registration for Accurate positioning which can increase production efficiency.

Stripping Section

– Triple action movement with upper, middle and lower stripping frame.

– Stripping pins or male / female die are available for different stripping jobs.

– Centreline registration for Accurate positioning which can increase production efficiency.

Delivery Section

– Automatic auxiliary belt table for nonstop delivery.
– Maximum pile height up to 1350 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of pile.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.

Delivery Section

– Automatic auxiliary belt table for nonstop delivery.
– Maximum pile height up to 1350 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of pile.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, thus prolonging the lifetime of the cutting plate.

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, thus prolonging the lifetime of the cutting plate.

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Main Drive System

– The patented toggle design contributes to a maximum diecutting pressure of 300 tons.
– The required pressure can be easily set up on touch screen, recorded for repeat jobs and controlled by electrical pressure adjustment system.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Main Drive System

– The patented toggle design contributes to a maximum diecutting pressure of 300 tons.
– The required pressure can be easily set up on touch screen, recorded for repeat jobs and controlled by electrical pressure adjustment system.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Main Motor

– Inverter-controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Main Motor

– Inverter- controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Gripper Finger

– Aluminium gripper bar and positioning system, gripper bar is a 1 piece design

– Made of lightweight and durable aluminium alloy with ultra-hard coat and anodized finish ensures accurate and consistent paper registration

Gripper Finger

– Aluminium gripper bar and positioning system, gripper bar is a 1 piece design

– Made of lightweight and durable aluminium alloy with ultra-hard coat and anodized finish ensures accurate and consistent paper registration

Options

– Feeding Section; 1. Pre loader for continuous runs. 2. Anti-static air blowing device for diecutting thin paper or plastic sheets.
– Feeding Table; Thin paper slow down device suitable for any thin paper and high speed diecutting.
– Diecutting section; Special heavy diecutting pressure up to 450 tons,
– Gripper Bar; Quick-lock bar device, oil cooling system.
– Stripping Section; Stripping pre make ready table, quick lock device for stripping frame
– Delivery Section; 1. Tape inserter, 2. Anti-static / thin paper air-blow device.

Options

– Feeding Section; 1. Pre loader for continuous runs. 2. Anti-static air blowing device for diecutting thin paper or plastic sheets.
– Feeding Table; Thin paper slow down device suitable for any thin paper and high speed diecutting.
– Diecutting section; Special heavy diecutting pressure up to 450 tons,
– Gripper Bar; Quick-lock bar device, oil cooling system.
– Stripping Section; Stripping pre make ready table, quick lock device for stripping frame
– Delivery Section; 1. Tape inserter, 2. Anti-static / thin paper air-blow device.

JY 106E corrugated board

JY 106E – Corrugated Board