yoco-logo

YOCO JY-106EB Blanking
Automatic Diecutter

For a more detailed technical presentation, click here

Feeder

– Machine comes equipped with German designed KBA feeding system.
– The height of the machine has been made taller to provide a pile height of 1600mm
– The machine is equipped with a non stop feeding device.
– There are 4 suction cups for lifting paper and 5 suction cups for moving the paper.
– The height and angle of the suction cups are easily adjustable to accommodate all grades of board from flat to warped.
– Optional; 1. pre loader for continuous run. 2. anti static air blowing device for diecutting thin paper or plastic sheets.
– Sheet thickness of 1.5-5mm corrugated board.

Feeder

– Machine comes equipped with German designed KBA feeding system.
– The height of the machine has been made taller to provide a pile height of 1600mm
– The machine is equipped with a non stop feeding device.
– There are 4 suction cups for lifting paper and 5 suction cups for moving the paper.
– The height and angle of the suction cups are easily adjustable to accommodate all grades of board from flat to warped.
– Optional; 1. pre loader for continuous run. 2. anti static air blowing device for diecutting thin paper or plastic sheets.
– Sheet thickness of 1.5-5mm corrugated board.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– Single position engagement ensuring the 1st sheet after a re-start always gets fed to the front lays for timesaving and material saving make ready
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– Single position engagement ensuring the 1st sheet after a re-start always gets fed to the front lays for timesaving and material saving make ready
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.
– The speed of the feeding belt is easily adjustable for perfect sheet control.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.
– The speed of the feeding belt is easily adjustable for perfect sheet control.

Diecutting Section

– The diecutting chase can easily be changed over to facilitate quick set of repeat jobs.
– The cutting force is micro-adjustable by worm gear driven by the motor and controlled by touch screen displays.
– The cutting chase uses pneumatic lock up system to increase efficiency.
– The cutting plate slides in and out easily using an air floating device alleviating weight.
– The machine has a centerline system on the diecutting chase with transversal micro adjustment to ensure accurate registration resulting in quick job changeover

Diecutting Section

– The diecutting chase can easily be changed over to facilitate quick set of repeat jobs.
– The cutting force is micro-adjustable by worm gear driven by the motor and controlled by touch screen displays.
– The cutting chase uses pneumatic lock up system to increase efficiency.
– The cutting plate slides in and out easily using an air floating device alleviating weight.
– The machine has a centerline system on the diecutting chase with transversal micro adjustment to ensure accurate registration resulting in quick job changeover

Blanking / Stripping Section

– Stripping and Single Station Blanking Section
– The machine can easily be changed over from normal striping functions to blanking functions.
– The carton can be blanked and piled correctly with a paper inserter option also available.
– The stripping section consists of an upper and lower frame. A male and female stripping die can also be used.
– Tooling is fixed into position using a centerline system throughout the machine.
– The blanking system is also equipped with a pile table and a non stop automatic auxiliary delivery belt.

Blanking / Stripping Section

– Stripping and Single Station Blanking Section
– The machine can easily be changed over from normal striping functions to blanking functions.
– The carton can be blanked and piled correctly with a paper inserter option also available.
– The stripping section consists of an upper and lower frame. A male and female stripping die can also be used.
– Tooling is fixed into position using a centerline system throughout the machine.
– The blanking system is also equipped with a pile table and a non stop automatic auxiliary delivery belt.

– The machine can blank the product and stack it on the table and the linked scrap will be transported to the delivery unit.
– The machine is equipped with a paper inserter, the operator can set the number of sheets to insert in the stack.
– Inserting the paper helps prevent the product falling down.
– The blank is pushed down through the lower (female) die by the upper (male) die. The finished blank is neatly stacked on a pallet

– Optional; 1. Quick lock device for stripping frame

– The machine can blank the product and stack it on the table and the linked scrap will be transported to the delivery unit.
– The machine is equipped with a paper inserter, the operator can set the number of sheets to insert in the stack.
– Inserting the paper helps prevent the product falling down.
– The blank is pushed down through the lower (female) die by the upper (male) die. The finished blank is neatly stacked on a pallet
– Optional; 1. Quick lock device for stripping frame

Delivery Section

– With automatic auxiliary belt table can realise nonstop delivery. Maximum pile height up to 1350 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of paper pile
– Lower air blow system suitable for thin paper diecutting.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.
– Optional; tape inserter, anti-static / thin paper air-blow device.

Delivery Section

– With automatic auxiliary belt table can realise nonstop delivery. Maximum pile height up to 1350 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of paper pile
– Lower air blow system suitable for thin paper diecutting.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.
– Optional; tape inserter, anti-static / thin paper air-blow device.

Aluminium Supporting Base

– The Aluminum support base is located under the cutting plate to serve as a cushion to reduce noise and to help protect the cutting plate.

– This also extends the life of the cutting plate.

– Accurate position of the cutting chase is controlled by precision photocell sensors along with an automatic chase lock device.

Aluminium Supporting Base

– The Aluminum support base is located under the cutting plate to serve as a cushion to reduce noise and to help protect the cutting plate.

– This also extends the life of the cutting plate.

– Accurate position of the cutting chase is controlled by precision photocell sensors along with an automatic chase lock device.

Gripper Finger

– Aluminum gripper bar that holds the gripper fingers are a two piece design.

– The gripper bars are made of light weight aluminum alloy with an ultra hard coat and anodized finish, ensuring accurate and consistent paper registration.

Gripper Finger

– Aluminum gripper bar that holds the gripper fingers are a two piece design.

– The gripper bars are made of light weight aluminum alloy with an ultra hard coat and anodized finish, ensuring accurate and consistent paper registration.

Main Motor

– Inverter-controlled main motor runs the machine up to a maximum speed of 7500 sheets per hour.

– Equipped with an overload protection device with torque limiter for the safety of the operator and equipment.

– Equipped with state of the art brake and air clutch imported from Europe.

Main Motor

– Inverter-controlled main motor runs the machine up to a maximum speed of 7500 sheets per hour.

– Equipped with an overload protection device with torque limiter for the safety of the operator and equipment.

– Equipped with state of the art brake and air clutch imported from Europe.

Electronics

– Omron PLC and Schneider inverter for controlling the motor.

– All electrical components are CE standard.

– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Electronics

– Omron PLC and Schneider inverter for controlling the motor.

– All electrical components are CE standard.

– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

JY106EB with single blanking function

JY 106