yoco-logo

YOCO 1450
Automatic Diecutter

For a more detailed technical presentation, click here

Feeder

– Equipped with German design feeding system offered by KBA-MMS
– Whole machine is risen making the maximum pile height up to 1400mm, also equipped with non-stop feeding device
– There are 4 suction cups each lifting paper and 5 other suction cups for moving paper; height and angle of suction heads are easily adjustable.
– The up and down of pile table can be adjusted by double-speed control system which micro-adjustment is available for transversal position of pile table
– Lateral blowing system is adopted to enhance paper separation. To detect double sheet during transportation, we have electronic sensors to do so.
– The installation of anti-obstacle device on the feeding section is to prevent obstacles from entering into the machine which may cause damages to the machine.
– Optional; 1. pre loader for continuous run. 2. anti static air blowing device for diecutting thin paper or plastic sheets.
– Sheet thickness of 1.5-5mm corrugated board.

Feeder

– Equipped with German design feeding system offered by KBA-MMS
– Whole machine is risen making the maximum pile height up to 1400mm, also equipped with non-stop feeding device
– There are 4 suction cups each lifting paper and 5 other suction cups for moving paper; height and angle of suction heads are easily adjustable.
– The up and down of pile table can be adjusted by double-speed control system which micro-adjustment is available for transversal position of pile table
– Lateral blowing system is adopted to enhance paper separation. To detect double sheet during transportation, we have electronic sensors to do so.
– The installation of anti-obstacle device on the feeding section is to prevent obstacles from entering into the machine which may cause damages to the machine.
– Optional; 1. pre loader for continuous run. 2. anti static air blowing device for diecutting thin paper or plastic sheets.
– Sheet thickness of 1.5-5mm corrugated board.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Feeding Table

– The pile table can be easily adjusted in all directions by a double speed control system while micro adjustment control.
– A blowing system is provided to enhance paper separation.
– There is an electronic sensor to prevent double sheet feeding.
– The machine is equipped with a device for preventing obstacles from entering the machine.
– Feeding belt provided by HABASIT, Switzerland.
– Optional; Thin paper slow down device suitable for any thin paper and high speed diecutting.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Side Lay

– Accurate paper registration is done using two micro adjustable front lays.
– On both sides of the feeding system there are push and pull side lays. The sensitivity of the photo sensors on the side lays and front lays can be adjusted to detect black paper or transparent plastic film.
– The pull and push side guides can be easily changed over by simply turning a bolt. This eliminates the need to remove and replace the complete side guide.

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Diecutting Section

– Cutting chase turn-over device to actualise short set up of repeat jobs
– Micro-adjustment of cutting force by worm gear driven by motor and controlled by touch screen.
– Pneumatic lock up system on diecutting chase to increase efficiency
– Easy slide in and out of diecutting plate is realised by air floating device
– Centreline system on diecutting chase with transversal micro adjustment ensures accurate registration thus results in quick job changeover

Stripping Section

– New designed 3 action movement structure with upper, middle and lower stripping frame facilitates die change
– Stripping pins or male / female die are available for different stripping jobs
– Match with the centreline registration system in diecutting section, the same system also applies to the stripping section to minimise changeover time. Accurate positioning can increase production efficiency.
– Optional; stripping pre make ready table, quick lock device for stripping frame.

Stripping Section

– New designed 3 action movement structure with upper, middle and lower stripping frame facilitates die change
– Stripping pins or male / female die are available for different stripping jobs
– Match with the centreline registration system in diecutting section, the same system also applies to the stripping section to minimise changeover time. Accurate positioning can increase production efficiency.
– Optional; stripping pre make ready table, quick lock device for stripping frame.

Delivery Section

– With automatic auxiliary belt table can realise nonstop delivery. Maximum pile height up to 1145 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of paper pile
– Lower air blow system suitable for thin paper diecutting.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.
– Optional; tape inserter, anti-static / thin paper air-blow device.

Delivery Section

– With automatic auxiliary belt table can realise nonstop delivery. Maximum pile height up to 1145 mm.
– Safety photo-electric devices prevent over-ascending and over-descending of paper pile
– Lower air blow system suitable for thin paper diecutting.
– Adjustable depressor brush helps unloading paper from grippers and piling up paper.
– Air-controlled rear alignment board switch design, easy to pick finished product sample
– Feeder movement and speed control can be adjusted at the delivery section
– Separate counting device is available.
– Optional; tape inserter, anti-static / thin paper air-blow device.

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, hence to prolong the lifetime of the cutting plate.

– Accurate positioning of cutting chase controlled by precision photocell sensors with automatic chase lock device

Aluminium Supporting Base

– Aluminium base plate is under the cutting plate to serve as a cushion to reduce noise and to protect the cutting plate, hence to prolong the lifetime of the cutting plate.

– Accurate positioning of cutting chase controlled by precision photocell sensors with automatic chase lock device

Gripper Finger

– Aluminium gripper bar and positioning system, gripper plate is 1 piece design
– Gripper bars with grippers made of lightweight and durable aluminium alloy with ultra-hard coat and anodized finish ensures accurate and consistent paper registration

Gripper Finger

– Aluminium gripper bar and positioning system, gripper plate is 1 piece design
– Gripper bars with grippers made of lightweight and durable aluminium alloy with ultra-hard coat and anodized finish ensures accurate and consistent paper registration

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Gripper Bar

– Unique design of gripper bar lock for compensation to ensure accurate paper registration
– All main drive chains are delivered in pairs from Japan and must undergo a special long-run test.

– Optional; quick-lock bar device, oil cooling system.

Main Drive System

– The patented toggle design contributes to maximum diecutting pressure of 400 tons.
– The required pressure can be easily set up on touch screen, controlled by electrical pressure adjustment system.
– Digital display of pressure data facilitates set up of repeat jobs.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Main Drive System

– The patented toggle design contributes to maximum diecutting pressure of 400 tons.
– The required pressure can be easily set up on touch screen, controlled by electrical pressure adjustment system.
– Digital display of pressure data facilitates set up of repeat jobs.
– Adopts automatic centralised lubrication system and automatic main drive chain lubricating system.
– New designed high pressure index drive system with gear drive for gripper bar positioning control.

Main Motor

– Inverter-controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Main Motor

– Inverter- controlled main motor contributes to maximum speed 7500 sph
– Overload protection device with torque limiter for the highest safety operator and equipment
– Equipped with reliable brake air clutch imported from Europe

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

Electronics

– Omron PLC and Schneider inverter for motor control
– All electronic components are CE standard
– Computerised control display and 3D touch screen operation can immediately trace and visualise machine status and possible machine stop causes.

yoco - 1450 specs